Marble Polishing Crème
RESTORE-IT™ is ready-to-use polishing cream that will re-polish worn marble, travertine, terrazzo, polished limestone. and may also be used to polish concrete after honing. RESTORE-IT™ provides the stone with a natural polish in the same manner the stone is polished at the factory using normal equipment. Water marks, etching from fruit juices and alcohol, as well as minor surface scratches can be removed while restoring a high degree of natural polish. Use RESTORE-IT™ on floors as well as countertops and furniture. Environmentally friendly; will resist “burning”. RESTORE-IT™ allows the natural stone to breathe; it contains no solvents and is VOC compliant.
Authorized UL ProductCode: 2502Packaging: 4 x 1 Gal./Case; 12 x 32 oz Qt./Case
- Product typePolishing Compound
- Safe on StoneYes
- AppearanceOpaque, viscous, white liquid
- Allows vapor transmissionYes
- Specific Gravity (g/cc)1.30 ± 0.01
- Increased GlossOutstanding
- pH0.5 - 1.0
- UL ClassifiedYes
- Flash PointNone
DocumentationTechnical Data Sheet Restore-It TDS English GHS.pdf Safety Data Sheet RESTORE-IT SDS English.pdf Secondary Label Restore-It (Undiluted) GHS Secondary Label 6 up.pdf
SURFACE PREPARATION: Surface must be clean. On floor surfaces, make sure all waxes, floor finish or other coatings are removed. If a coating is on the floor, use NCL HURRICANE™ Intensive Stone Cleaner for removal.
PLEASE NOTE: Worn out or damaged surfaces may require resurfacing prior to polishing.
APPLICATION: (NOTE: SHAKE BOTTLE WELL BEFORE USE.) Protect all adjacent areas to the intended restoration surface. All adjacent carpet, wood, glass, polished brass and other non-masonry surfaces should be covered or otherwise protected from any possible overspray from machinery or other contact with this product. When work area has been cleaned and all adjacent areas have been protected, moisten the work area with clean water and apply RESTORE-IT™ (normally 2 oz. per each 15 sq. ft. or 1.39 sq. meters of restoration). Add enough water to make the cream into a flowable slurry and polish the surface with a low speed machine and a red or white polishing pad. Most stone surfaces need only 4 or 5 passes (east-west / north-south) in each direction for re-polishing; however, you should test in a small area to determine the time required for your situation. When re-polishing is achieved, vacuum the slurry; immediately flood rinse the work area and vacuum again. Towel dry and move to next area. Work in small, manageable areas (approx. 4’ X 4’, 1.48 sq. meters) and complete the work in a checkerboard fashion backing toward the exit.
DO NOT TRACK SLURRY OVER COMPLETED AREAS.
Protect completed areas form overspray by wetting with clean water. After the entire job is complete, rinse well with clean water or a mild solution of NCL HURRICANE (1 oz. per gallon of water) and vacuum well.
For daily maintenance after re-polishing, use the SCS Daily Maintenance System (PATINA™-HURRICANE™); see the STONE CARE SOLUTIONS™ brochure for more information.
IMPORTANT NOTES: Black marbles are more sensitive than most other marble surfaces and require more care when re-polishing. - Most green marble surfaces and some white marble surfaces will not re-polish using this method.
Contact NCL for alternative procedures. - Severely worn surfaces may require mechanical resurfacing prior to re-polishing.
Features & Benefits
- Black marbles are more sensitive than most other marble surfaces and require more care when re-polishing.
- Most green marble surfaces and some white marble surfaces will not re-polish using this method.
- Contact NCL for alternative procedures.
- Severely worn surfaces may require mechanical resurfacing prior to re-polishing.
No Video Available
DANGER: CAUSES SEVERE SKIN BURNS AND EYE DAMAGE. MAY CAUSE RESPIRATORY IRRITATION. KEEP OUT OF THE REACH OF CHILDREN
Prevention: Do not breathe dust or mist. Wash thoroughly after handling. Wear protective gloves/protective clothing/eye protection/face protection. Use only outdoors or in a well-ventilated area.
Response: If swallowed: Rinse mouth. Do NOT induce vomiting. If on skin (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower. Wash contaminated clothing before reuse. If inhaled: Remove person to fresh air and keep comfortable for breathing. Immediately call a poison center/doctor. If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
Storage: Store in a well-ventilated place. Keep container tightly closed. Store locked up.
Disposal: Dispose of contents/container in accordance with local/regional/national/international regulations.
This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200.
Additional safety measures:
Read the entire label and SDS before using this product, and for additional first aid measures. SDS for this product is available under the Documents tab.